What is the BEST limiter/maximizer ??
What is the BEST limiter/maximizer ??
Hi !!!!!!!!!!!!!
I would know what is the BEST limiter/maximizer plugin?
I use Sonic Timeworks mastering compressor because he improves the RMS and the colour of the sound of my tracks.
The Kjaerhus golden peak pressor has got a very good colour of sound BUT he can't improve the RMS as Sonic Timeworks mastering compressor.
Also the PK3 mastering limiter is very good but he don't work with Wavelab (when I render the PK3 doesn't apply my values...).
I know the others limiters are not performant... (Waves, Voxengo...).
We are together !!!!
Fred
I would know what is the BEST limiter/maximizer plugin?
I use Sonic Timeworks mastering compressor because he improves the RMS and the colour of the sound of my tracks.
The Kjaerhus golden peak pressor has got a very good colour of sound BUT he can't improve the RMS as Sonic Timeworks mastering compressor.
Also the PK3 mastering limiter is very good but he don't work with Wavelab (when I render the PK3 doesn't apply my values...).
I know the others limiters are not performant... (Waves, Voxengo...).
We are together !!!!
Fred
Hi buddy,
for simply increasing the volume, L2 from waves is best, but it when you push it hard it
tends to pump slightly and give the audio a warm result.
For transparent limiting izotope holds up very well without colouring the sound too much.
Ive also heard the wave-arts limiter is very transparent.
For a good whack check out the T-Racks preset the legendary guys on this forum have come across.
Cheers
for simply increasing the volume, L2 from waves is best, but it when you push it hard it
tends to pump slightly and give the audio a warm result.
For transparent limiting izotope holds up very well without colouring the sound too much.
Ive also heard the wave-arts limiter is very transparent.
For a good whack check out the T-Racks preset the legendary guys on this forum have come across.
Cheers
-
- Posts: 10
- Joined: Thu Dec 14, 2006 7:47 pm
Jazzbazzjazzbass12 wrote:Isnt the limiter in Har Bal just as good? Can you use this for your final limiter.
If I had a ref. with a RMS of -12 and a peak of 3, if I do Loudenss match, I should not need to export to Soundforge and use a L2?
Thanks
You are correct. The limiter in Har-Bal is just fine. The problem occus when the limiter is pushed too hard. If you are going for loudness use a wideband compressor.
In Har-Bal I generally increase the gain until I can see (one) dot in the meter and that usually translates between -11 and -12dB's which is suitable for commercial whil still maintaining the punch.
Paavo and I have a major surprise coming up in the next version which will be 1/12th Octave Resolution.
The sound is out of this world and you will not have the slighest bit of tinniness generally associated with digital software.
I have actually mastered an entire album just using the new version of Har-Bal.
I have tested it on the worst tracks I can find and was blown away at the improvement.
We are looking at January 2007 for a release date.
Cheers
Earle
Last edited by har-bal on Tue Dec 19, 2006 7:20 pm, edited 1 time in total.
-
- Posts: 10
- Joined: Thu Dec 14, 2006 7:47 pm
Jazzbass12jazzbass12 wrote:So,
I would put my wave into to Har Bal. set up my eq to taste-import to Sound Forge and Multi Band Comp if need be then put backinto Har balance and then limt and add air if needed?
It's not on Jan 7th. It will be sometime in January.
You may not need to use a MultiBand Compresor when you see what 1?12 Octave resolution does for you. We just have to make sure we communicate the proper use to our customers so there can be no misunderstandings.
Cheers
Earle
Last edited by har-bal on Wed Dec 20, 2006 4:47 pm, edited 1 time in total.
-
- Posts: 10
- Joined: Thu Dec 14, 2006 7:47 pm
not too beat this to death..... I have a track that is on the bassy side (low end mud).
I rolled off below 45 in HB as you suggested elswhere. I then dump into SForge and try to Multi comp a fix with Wave LinMB. Any suggestion for using the MB effectivley to fix an overly bassy low end?
Thanks,
Rich O
I rolled off below 45 in HB as you suggested elswhere. I then dump into SForge and try to Multi comp a fix with Wave LinMB. Any suggestion for using the MB effectivley to fix an overly bassy low end?
Thanks,
Rich O
Jazzbass12jazzbass12 wrote:not too beat this to death..... I have a track that is on the bassy side (low end mud).
I rolled off below 45 in HB as you suggested elswhere. I then dump into SForge and try to Multi comp a fix with Wave LinMB. Any suggestion for using the MB effectivley to fix an overly bassy low end?
Thanks,
Rich O
Send me the track as a wave file. Go to my main site www.hdqtrz.com and upload it using the tool. I have the email address listed on the page.
Cheers
Earle
-
- Posts: 10
- Joined: Thu Dec 14, 2006 7:47 pm
-
- Posts: 10
- Joined: Thu Dec 14, 2006 7:47 pm
L2 reverse engineered
Hi Fred ,
To weigh in on your original question ... IMO , the 'best' limiter is one that is the clean , and offers the most flexibility in terms of controlling attack/release , mode ( RMS/peak ) , can be hard/soft , has a variable knee , and switchable/adjustable look-ahead .. Many 'mastering' limiters offer little more than a theshold .... which is very limiting ( excuse pun ) in terms of controlling tonal issues ( in other words it's difficult to avoid a harsh , thin sound ) .
The commonly praised L2 is , in my opinion , excessively minimal in control , grainy/muddy ( even after disabling ARC ) but , by substituting more suitable units , can be emulated with an upward expander ( WAVES C1/Rennaissance ) , followed by a versatile limiter .
Cheers ,
Evan .
To weigh in on your original question ... IMO , the 'best' limiter is one that is the clean , and offers the most flexibility in terms of controlling attack/release , mode ( RMS/peak ) , can be hard/soft , has a variable knee , and switchable/adjustable look-ahead .. Many 'mastering' limiters offer little more than a theshold .... which is very limiting ( excuse pun ) in terms of controlling tonal issues ( in other words it's difficult to avoid a harsh , thin sound ) .
The commonly praised L2 is , in my opinion , excessively minimal in control , grainy/muddy ( even after disabling ARC ) but , by substituting more suitable units , can be emulated with an upward expander ( WAVES C1/Rennaissance ) , followed by a versatile limiter .
Cheers ,
Evan .
" I hate compression with a vengeance . I avoid it . I'm a great believer in the dynamic range being preserved " Alan Parsons
I posted about a new broadband brickwall limiter I found that I really like on another thread, but i'll quote it here:
http://www.voxengo.com/product/elephant/
Here's my default settings for that, if you're wondering:
http://ictybtihky.com/harbal/pluginshot ... ephant.gif
I'll be posting a thread here soon, with the expanded list of my testing of various "leading" broadband brickwall limiters, as a function of THD. I think you might be surprised at how much Elephant walks all over everything else, including Waves L2. Unfortunately I won't be adding Waves L3-16 to the list, because I can't justify buying the Waves Limiter package since I won't be using it, and I sure as h-e-double-hockey-sticks can't afford Waves Carbon within the next decade and/or ever.![Razz :P](./images/smilies/icon_razz.gif)
And of course I can't finish off this post without mentioning that yes, I think Voxengo Elephant is KING of transparency, for a little OR a ton of limiting.I found another great broadband brickwall limiter. It's not as transparent as Voxengo Elephant, especially on the treble transients, but for some things it just sounds better, especially if you aren't working with stuff that has very loud or very linear treble transients.
Crysonic Spectra'Phy
http://www.crysonic.com/spectraphy.html
check it out.I like it almost as much as Elephant all around, it really is great for stuff you need a vintage touch on at the brickwall limiter stage. In fact, it's too bad they can't release a plugin that only has the "Drive/Color" function, because that sounds wonderful.
http://www.voxengo.com/product/elephant/
Here's my default settings for that, if you're wondering:
http://ictybtihky.com/harbal/pluginshot ... ephant.gif
I'll be posting a thread here soon, with the expanded list of my testing of various "leading" broadband brickwall limiters, as a function of THD. I think you might be surprised at how much Elephant walks all over everything else, including Waves L2. Unfortunately I won't be adding Waves L3-16 to the list, because I can't justify buying the Waves Limiter package since I won't be using it, and I sure as h-e-double-hockey-sticks can't afford Waves Carbon within the next decade and/or ever.
![Razz :P](./images/smilies/icon_razz.gif)